Woodhaven 1826: Drill Press Table Manuel d'utilisateur télécharger pdf

1826

Drill Press Table

Please Read Carefully!

BEFORE BEGINNING

Identify and verify that you have all the parts listed. Read

the instructions at least once, familiarizing yourself with the

parts and assembly instructions before beginning. You’ll need a

#3 Phillips screwdriver and a 7/16" wrench for assembly.

ASSEMBLY

Insert a 1" screw (MF015) thru the four countersunk holes

in the drill press table (1826A), place the table upside down on

a flat surface and start an oval nut (5760B - raised side first)

on the end of the screws. Slide a 8" Ultra Track (4408) on two

oval nuts until it's centered end-to-end on the oval nuts and the

face of the Ultra Track is flush with the edge of the drill insert

(1826B) opening, then tighten the screws. See fig. 1 & upper

inset photo.

Install two 1" washers (WFN002) on each 3/4" bolt

(HB020), insert the bolts thru the holes in the leveler (1826D)

and start an oval nut (5760B - raised side first) on the bolt ends.

Install the levelers on the Ultra Track by inserting the

oval nuts into the T-slot of the track. Position the levelers over

the drill insert, with the edge of the levelers resting against the

underside of the drill insert, tighten the bolts.

See fig. 1 & lower inset.

Parts List:

Part Description Quantity

1826A Drill Press Table . . . . . . . . . . . . . . . . . . . . . . . 1

1826B Drill Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1826C Square Washer . . . . . . . . . . . . . . . . . . . . . . . . 4

1826D Leveler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4408 8” Ultra Track . . . . . . . . . . . . . . . . . . . . . . . . . 2

NUT015 Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

HB050 1-1/2" Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

HB020 3/4" Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

MF015 1" Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

WFN002 1" Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5760B Oval Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

WL001 Lock washer . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1826D

4408

1826D

1 2

Drill Press Table 1

Résumé du contenu

Page 1 - Drill Press Table

1826Drill Press TablePlease Read Carefully!1BEFORE BEGINNING Identify and verify that you have all the parts listed. Read the instructions at least

Page 2

On each of the 1-1/2" bolts (HB050), install a square washer (1826C), a 1" washer (WFN002), a lock washer (WL001) and a nut (NUT015). Inser

Commentaires sur ces manuels

Pas de commentaire

Woodhaven 1826: Drill Press Table Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Woodhaven 1826: Drill Press Table. Woodhaven 1826: Drill Press Table User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Woodhaven 1826: Drill Press Table