Woodhaven 4965: Super Sled Manuel d'utilisateur télécharger pdf

Part Desc . . . . . . . . . . . . . . . . . . . . . . . . . Qty

4924B 24" Jig Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965A 32" Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965B Sled Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965C Fence Brackets, Pair . . . . . . . . . . . . . . . . . . . . . . . . 1

4965D Track Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6305A Outboard Clamp Bracket . . . . . . . . . . . . . . . . . . . 2

6305IC Inboard Clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4519 Straight Flip Stop . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Parts List

4965 Super Sled

Owners Manual

Please Read Carefully!

Part# Description Qty.

5760B Oval Nut 5

Part# Description Qty.

HB030 1" Bolt 3

Part# Description Qty.

BUSH004 5/8" Spacer 1

Part# Description Qty.

WS002 Washer 6

BEFORE BEGINNING

Identify and verify that you have all the parts listed in

the parts list above, plus the parts shown on this page. Read

through the instructions at least once before beginning. You'll

need a #2 & #3 Phillips screwdriver for assembly.

The Super Sled is designed to be used on a table saw at

least a 27" deep with a 3/8" x 3/4" miter slot that's between

4-1/2" and 7-1/2" from the blade, measured from the blade

side edge of the slot. It can be used in the left or right miter

slot. Do not attempt to use on table saws with tables smaller

than 27". If necessary, add additional supports to your saw to

prevent the saw from tipping.

For the Super Sled to work properly, the miter slot of

your saw must be parallel to the saw blade. If this is not the

case, make those adjustments to your saw before proceeding.

Part# Description Qty.

BUSH001 1/8” Spacer 2

Part# Description Qty.

5590 Knob 1

Part# Description Qty.

MF006 5/8" Screw 4

Part# Description Qty.

NUT025 Square Nut 4

Part# Description Qty.

5864 Ratchet Handle 2

Part# Description Qty.

5540 T-Knob 2

Part# Description Qty.

BUSH002 1/4" Spacer 2

Part# Description Qty.

4965PA Index Pin 2

Part# Description Qty.

5505 Thumb Screw 1

Part# Description Qty.

MP150 1-1/2" Screw 2

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Owners Manual

Part Desc . . . . . . . . . . . . . . . . . . . . . . . . . Qty4924B 24" Jig Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 2 - Taper Setup:

1Crosscut Setup: The Super Sled rides in the miter slot of the saw. Follow the instructions that come with the Jig Bar (4924B), install the hardware

Page 3 - Crosscut Fence Setup:

2FENCE BRACKET ASSEMBLY The vertical fence configuration is normally used for crosscuts. Insert two 5/8" screws (MF006) thru the countersink hol

Page 4

3FENCE INSTALL FOR TAPERS The horizontal fence configuration is normally used for tapers. Install a washer (WS002) and a 1/8" spacer (BUSH001) o

Page 5

SLED OPERATION: Be sure to observe all safety precautions when using the table saw. The cut-off from your work can be thrown by the table saw blade a

Page 6

5SLED OPERATION CONTINUED:7Crosscut Fence Setup - Horizontal - Example 1: The horizontal fence configuration can be used for crosscuts, but is not re

Page 7

USING THE SUPER SLED FOR CROSSCUTS After setting the Fence angle, place the work on the Sled Base, butted against the Fence and the Flip Stop. Slide

Page 8

OPTIONAL ACCESSORIES The 6305R Riser Kit increases the capacity of the toggle clamps to 2-3/4" thick stock. The 3690 Mite-R-Gage is a handy tool

Commentaires sur ces manuels

Pas de commentaire

Woodhaven 4965: Super Sled Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Woodhaven 4965: Super Sled. Woodhaven 4965: Super Sled User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Woodhaven 4965: Super Sled