Woodhaven 4951: Large Cut-Off Sled Manuel d'utilisateur télécharger pdf

Miter Bar being installed

on MDF Base. Bar

will be ﬂ ush with

edge of base.

BEFORE BEGINNING

Identify and verify that

you have all the parts listed

and read thru the instructions

at least once before beginning.

All set-up work should be done

with the saw disconnected from

the power and the saw blade

lowered below the table. This unit is designed for table saws with

at least a 27" deep table. Do not attempt to use on table saws with

smaller tables. If necessary, add additional supports to your saw

to prevent the saw from tipping. This unit relies on the miter slot

of your saw being parallel to the saw blade for it to work properly.

If this is not the case, make those adjustments to your saw first.

MOUNT THE MITER BARS TO THE MDF BASE

Prepare the Miter Bars according to the instructions

that come with them, using the hardware included.

The Cut-Off Sled can be used with the miter bars in

either miter slot. We suggest you mount it in the miter slot you

normally use your miter gauge in. Place the miter bars (4918B)

with the countersunk holes facing down, in the miter slot. There

are mounting holes for the miter bars in one of the MDF bases

(4951D). Align the mounting holes in the MDF base with the

threaded holes in the bars. Position the base over the bars so

that it overhangs the cutting path of the saw blade by 1/2"

or less. Attach the bars to the base with the 1" screws. The

bars will overhang the base approximately 2" at each end. Re-

check the fit of the bar/base assembly, making sure it slides

smoothly, readjusting the plugs as necessary. See fig. 1.

Parts List:

Please identify and verify that you have all of the

hardware shown below prior to assembly.

Part Description Quantity

4951D MDF Base . . . . . . . . . . . . . . . . . . . . . . . . . 2

4918B 17-3/4" Miter Bar . . . . . . . . . . . . . . . . . . 2

4951E Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4951B Brace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4424 24" Ultra Track . . . . . . . . . . . . . . . . . . . . 2

4412 12" Ultra Track . . . . . . . . . . . . . . . . . . . . 2

4951C 24" Sub-Fence . . . . . . . . . . . . . . . . . . . . . 2

4951S Straight Stop . . . . . . . . . . . . . . . . . . . . . . 1

3724R/L 24" Left & Right Tapes . . . . . . . . . . . . . 1

4951

Large Cut-Off Sled

Please Read Carefully!

Part# Description Qty.

5771B 3/4" Screw 4

Part# Description Qty.

HB030 1" Bolt 20

Part# Description Qty.

5760B Oval Nut 36

Part# Description Qty.

WB002 Washer 20

Part# Description Qty.

MF010 3/4" Screw 12

4918B 4951D

4918B

1 2

Large Cut-Off Sled 1

Résumé du contenu

Page 1 - Large Cut-Off Sled

Miter Bar being installed on MDF Base. Bar will be ﬂ ush with edge of base.BEFORE BEGINNING Identify and verify that you have all the parts listed and

Page 2

Turn the saw on and cut off the overhanging edge of the base (This should be no more than 1/2"!), guiding the bar/base in the miter slot, past

Commentaires sur ces manuels

Pas de commentaire

Woodhaven 4951: Large Cut-Off Sled Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Woodhaven 4951: Large Cut-Off Sled. Woodhaven 4951: Large Cut-Off Sled User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Woodhaven 4951: Large Cut-Off Sled