Woodhaven Router Plate and Table Manuel d'utilisateur télécharger pdf

GENERAL INSTRUCTIONS

Some routers will require cocking one handle in and

partially under the table followed by the other handle, unless the

handles can be removed. ”D” handle or pistol grip routers will

not work on our plate in a table unless the handle is removed.

STORING THE ROUTER - READ ME!!!!!

Our plates are resistant to sagging and flexing during

use. However, long term storage of your router in the

table is not advisable. Prolonged hanging may cause

the plate to sag, proving again that gravity works.

After use, store the router (leave the plate attached) in

an upright position with the plate laying on a flat surface.

147 OR 147AP INSERT PLATE - PATENT #5,699,844

Be sure the O-ring is installed completely in the groove

of the router plate. We install the O-ring at our factory, but

sometimes they partially work their way out during shipping.

Before installing an insert, first determine which side

of the insert is the bottom. The bottom of the insert has a

machined face that is either black or dull yellow. The insert

snaps into the opening in the plate. Install the insert by

placing a bottom edge of the insert, at an angle, down into

the opening and then pressing the opposite edge into place.

Turn the insert 1/4 turn to be sure it is seated

on the O-ring. Test to be sure that it is held in place

and will not fall out. Extra inserts are available.

To remove the insert, reach underneath the plate and press

up, or insert a flat blade screwdriver in the slot in

the insert from above the plate and pry out.

If the insert falls out, lifts out or turns without

resistance, or the insert will not seat properly in the

opening, then replace the O-ring. The O-ring is a wear

item and will need to be replaced periodically. Always

check that the insert fits properly before using the

router. DO NOT use the plate if the insert is loose!

STARTING PIN

The starting pin is used with piloted type bits to aid in

starting the cut in an odd or irregular shaped piece where

it is impossible to use a router fence. It is a safety device

and should be used in lieu of trying to start the cut freehand.

If there is more than one starting pin hole in your router

plate, always use the one to the right of the router bit.

Router Plate

Instructions

Please Read Carefully!

Parts List

Quantity Item

1 . . . . . . . . . . . . . . . . 147/147AP

1 . . . . . . . . . .101A Starting Pin

1 . . . . . . .140R O-ring, in plate

Plate Inserts

1 . . . . . . . . . 140B Blank Insert

1 . . . . . . . . 140D 1-3/16" Insert

1 . . . . . . . . . . . . . 140E 2" Insert

1 2 3 4

Résumé du contenu

Page 1 - Instructions

GENERAL INSTRUCTIONS Some routers will require cocking one handle in and partially under the table followed by the other handle, unless the handles c

Page 2 - Mounting

2LAYOUT, MARK & DRILL PLATE Side “B” is the side of the plate the router attaches to. Side ”A” is the working side of the plate and must be count

Page 3 - 2.33" radius

PC 690-93 PC 892 & 7529DeWalt 616/618Makita RF1101Hitachi M12VC4.005" approx.2.3125" radius4.062" approx.2.875" radiusPC 7518/

Page 4 - Router Table

5. TABLE FLATNESS SPECS Our tops are guaranteed flat to within .001 (one thousandths of an inch) per 1" of table length. For example, a 24"

Commentaires sur ces manuels

Pas de commentaire

Woodhaven Router Plate and Table Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Woodhaven Router Plate and Table. Woodhaven Router Plate and Table User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Woodhaven Router Plate and Table