Woodhaven 7660: Large Half-Blind Router Table Dovetail Jig w Manuel d'utilisateur télécharger pdf

Parts List

Please identify and verify that you have all of the parts.

Part Description Quantity

7650 Half-Blind Dovetail Jig, pre-assembled . . . . . . . 1

7650 Small

Half-Blind Router

Table Dovetail Jig

Please Read Carefully!

1.3125

(1-5/16”) (1-1/16”)

(1/4”)

(1/2”)

0.25 0.5

1.0625

Stop Position:

The Stop position controls the location of the first PIN/

TAIL & SOCKET where the drawer bottom groove will

eventually be cut (after machining the dovetails) in all the drawer

parts. The groove is normally centered in the first dovetail socket

from the bottom of the drawer so it is hidden after assembly.

The location of the bottom of the groove is usually between 1/4"

(for side mounted drawer guides) to 1/2" (for bottom mounted

drawer guides) from the bottom edge of the drawer. The Stop is

pre-set at 1-5/16" from each end of the Template, which positions

the bottom of the groove at 1/4" from the drawer bottom. (You

may cut into the stop slightly at this setting, which is OK.)

Repositioning the Stop to 1-1/16" from each end

of the Template will position the bottom of the groove at

1/2" from the drawer bottom.

Before Beginning:

Identify and verify that you have all the parts

listed. Read the instructions at least once,

familiarizing yourself with the parts before beginning.

For adjustments, you’ll need a 7/16" socket wrench.

The 7650 Half-Blind Dovetail Jig is designed for

router table use only. It cuts the common 7/8" on-center

dovetail spacing using stock from 1/2" to 3/4" thick,

up to 7-3/8" wide and a minimum of 6" long.

Set Bit Height:

You’ll need a table mounted router. Install the Dovetail

Bit (61780) in your router and set the bit height at 25/32"

using the Bit Gauge (7650B - attached to back of Ultra Track).

The bit height may need to be adjusted later (Step 8) after making

a test cut.

Alternately you can use a 5/8" guide bushing & locknut

(5030K, not included) and a 1/2" diameter x 14º dovetail bit with

a 1/2" shank (61404, not included). If using your own bushing,

make sure the nose isn’t over 1/2" long.

7650B

25/32”

Stop

1 2 3 4

Résumé du contenu

Page 1 - Table Dovetail Jig

Parts ListPlease identify and verify that you have all of the parts. Part Description Quantity7650 Half-Blind Dovetail Jig, pr

Page 2

2Assembled Drawer ComponentsSide should be inset 1/64” or less from end of Face. Drawer Side: Inside FaceDrawer Side: Inside FaceDrawer Back: Inside F

Page 3

3Adjust Clamps: Slide the Clamps to position the clamp pads on either side of the stock. Adjust the clamp pads to the stock thick-ness by holding the

Page 4 - Joint Fit - Tightness:

4Move Template back to increase the amount the drawer front/back will stick out past the side.Move Template forward to decrease the amount the drawer

Commentaires sur ces manuels

Pas de commentaire

Woodhaven 7660: Large Half-Blind Router Table Dovetail Jig w Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Woodhaven 7660: Large Half-Blind Router Table Dovetail Jig w. Woodhaven 7660: Large Half-Blind Router Table Dovetail Jig w/Bit User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Woodhaven 7660: Large Half-Blind Router Table Dovetail Jig w